How to Winterise a Pressure Washer (and the Water Tank in Your Van)
The first hard frost usually announces itself the same way. You go out to the van at half seven, start the machine, pull the trigger and get nothing. Or you get water weeping from the side of the pump head, which is worse. One clear, still night is all it takes, and the van on the drive got just as cold as everything else.
The problem is water left sitting in the kit. AR, the pump maker, explains it plainly: water expands as it freezes, and a pump left full of it can end up with broken plungers, damaged packings and a ruptured manifold. This guide covers what the machine and pump makers say, the accessories they leave to you, and the van tank that feeds it all.
Quick answer: If the machine can't sleep somewhere frost-free, drain it and put antifreeze through it. Kärcher's manual for its HDS C hot-water machines says to take off the hoses, drain the heating coil at the boiler base, run the machine for no more than 1 minute to empty the pump and lines, then flush antifreeze through with the burner off. Cat Pumps and AR both use a 50/50 mix of antifreeze and water. Bring the hoses, gun, lance and surface cleaner indoors, and empty the van tank's feed hose and filter bowl.
What actually breaks
The damage happens wherever water is trapped in a tight space:
- The pump head and unloader, the expensive end of the machine
- The heating coil on a hot-water machine, a long run of pipe that stays full unless you drain it
- The gun, lance and nozzles, which hold water behind the trigger valve
- The surface cleaner, in its swivel and spray bar
- Hoses and couplings, where ice can split a hose or ruin an O-ring
- The filter bowl and valves on the feed from your van tank
A cracked pump head or a split coil is a repair bill plus the days the van can't work. If you've worked out your day rate (our pricing guide shows how), you know what each of those costs.
Frost night or laying up for winter?
Kärcher's HDS C manual (it covers the HDS 6/14-4 C, 8/18-4 C/CXA and 9/17-4 C/CXA) says a machine that hasn't been completely drained should be stored somewhere frost-free. For longer breaks, or whenever frost-free storage isn't possible, it says to drain it and flush it with antifreeze. A van on the drive isn't frost-free, so the only real question is whether you're working tomorrow.
| Where the machine sleeps | What to do |
|---|---|
| Indoors, somewhere that stays above freezing | Drain the hoses, gun, lance and surface cleaner, and bring them in too |
| In the van, working again tomorrow | Drain the machine, antifreeze it, and bring the accessories indoors |
| In the van or a cold garage until spring | The full shutdown below, plus the van tank drained right down |
A garage or lock-up only counts if it actually stays above freezing, and plenty don't. A cheap thermometer that records the overnight low will settle it.
How to drain and antifreeze the machine
These steps follow the Kärcher HDS C manual and Cat Pumps' winterising bulletin. Your own machine's manual comes first, because drain points and run times vary.
- Finish on clean water. Cat says to flush the pump and chemical injector with fresh water, and Kärcher says to empty the detergent tank.
- Switch off and squeeze the gun trigger to release the pressure, as Cat's bulletin says.
- Take off the water supply hose and the high-pressure hose.
- Run the water out. On a hot-water machine, open the coil drain first (see below). On a Kärcher HDS C, the run is no more than 1 minute, until the pump and lines are empty. Don't run any machine dry for longer than its manual allows.
- Put the antifreeze through. Cat's method is a short hose (4 feet, about 1.2 metres) on the pump inlet, the other end in a container of the 50/50 mix, running the unit until antifreeze comes out of the discharge. On a Kärcher HDS C, you pour it into the float tank and run the machine with the burner off until it's fully flushed.
- Catch what comes out. Kärcher's manual for its HDS ST machines says to put a catch pan under the high-pressure outlet while you flush.
- Store it with the ports open. Cat says not to plug the inlet and discharge ports, and to cover the unit against the weather.
Kärcher adds that the antifreeze gives some protection against corrosion too.
Which antifreeze?
Kärcher's manual says a commercially available antifreeze, used according to its maker's handling instructions. Cat and AR give a 50/50 mix with water, and AR adds that you should follow local environmental rules. In England, the government's pollution prevention guidance for businesses says only clean water should go into a surface water drain, because those drains run straight into the environment. Scotland, Wales and Northern Ireland have their own guidance. If your own manual names a type, use that. It all comes back out at the next start-up, so in practice:
- Run the first water into a bucket, never onto a customer's drive or into a drain
- Keep the mix in a sealed, labelled container, out of reach of children and pets
- Don't re-use the same bucket all winter, because it picks up water each time and gets weaker
- When a mix is finished with, get rid of it the way the antifreeze maker's label says
AR also lists two alternatives: frost-free storage, or turning off the inlets and blowing the system out with air at 30–70 psi (roughly 2–5 bar).
Hot-water machines: drain the coil
On a hot box, the heating coil is the part you least want to split, because it stays full of water after you switch off. Both Kärcher manuals add a step to the drain-down: unscrew the supply line at the base of the boiler and let the coil drain. Refit the line before the antifreeze goes through, with the burner off. On any other make, find the coil drain in its own manual rather than guessing.
Hoses, gun, lance and surface cleaner
Kärcher's HDS ST manual warns that water left in the machine and its accessories can damage both as it freezes. In practice:
- Hoses: uncouple both ends, lift one end and walk along it so the water runs out, then coil it loosely and take it indoors. A hose left on the van's reel holds water along its whole length.
- Gun and lance: split them at the coupling, hold the gun nozzle-down and squeeze the trigger so it drains, and bring the nozzles in with them.
- Surface cleaner: tip it on its edge and turn the bar by hand so water drains out of the swivel and spray arms.
- Softwash and 12-volt pumps: drain the lines and check the pump's own manual for frost.
The van tank, its pipework and filters
A tank holding a few hundred litres takes a long time to freeze through, so in a normal UK frost the tank itself is rarely what goes. The thin stuff around it does: the outlet, the valve, the feed hose, the filter, and any pump on the tank.
On a frost night:
- Close the tank outlet valve and disconnect the feed hose at the machine.
- Drain the feed hose and anything else between the valve and the machine.
- Empty the filter bowl. Unscrew it, tip it out and refit it dry. A clear plastic bowl with ice in it cracks easily.
- Open any drain points below the valve, and close them in the morning before you open the tank.
Laying up for winter? Drain the tank right down, leave the outlet open, and rinse it before you refill in spring. Never put antifreeze in the tank itself: everything in there ends up on a customer's drive. Water-fed pole kit needs the same care, so follow its own manual.
Starting up again
The morning after a frost, or in spring, don't just fire it up and pull the trigger. Cat's bulletin says to:
- Turn the regulator or unloader to its lowest pressure
- Check the crankcase oil level, and that the oil is clean
- Reconnect the supply and discharge, and let water flow through the pump for 2–3 minutes
- Check every connection for leaks
- Turn the crankshaft by hand, and only start it if it moves freely
- Bring the pressure back up gradually
AR says to make sure there's no slush anywhere in the system first, because slush damages it and could injure you. If a hose or gun has frozen, thaw it indoors rather than forcing water through it.
If a frozen morning makes you late, say so early:
Hi Sarah — hard frost here this morning, so I'm letting the kit thaw properly before I run it. I'll be with you around 10 rather than 9. Nothing you need to do your end.
Frequently asked questions
Can I leave my pressure washer in the van over winter?
Only once it's been drained and flushed with antifreeze. Kärcher's manual says a machine that hasn't been fully drained belongs somewhere frost-free, and an unheated van isn't. Bring the accessories indoors either way.
Do I really need to do this every frost night?
If the machine sleeps in the van and frost is forecast, yes. Kärcher's manual only gives two ways to handle frost: frost-free storage, or draining and antifreeze. Once it's a habit, it's just part of packing up.
My pump froze overnight. Is it ruined?
Not necessarily, but don't start it until it's fully thawed, because AR warns against running with slush in the system. Then look for cracks or water weeping from the pump head and unloader, and follow Cat's restart. A weeping head needs a repair before it goes back to work.
The bottom line
Frost damage comes from water trapped in small spaces. If the kit can't sleep somewhere frost-free, drain it and antifreeze it the way your manual says, bring the accessories indoors, and empty the van tank's feed and filter. Then start it at its lowest pressure and bring it up gradually, as Cat's restart says.
MossyKit can't drain a pump for you. That part's you and a bucket. What it can do is keep the diary moving while the kit's thawing or laid up: a quote can go out with a date on it, and when the customer accepts it online, that date is booked into your Diary and you both get a "Booking confirmed" email, as long as you're not already full that day. See how it works in the no-signup demo.
Stop pricing jobs by hand
MossyKit turns a customer's address into a professional, priced quote in under 2 minutes. We'll set it up with you on a short call.
Book a demo